solder ball valve
three way control valve
vee ball valve
A ball valve is a rotational motion valve . The ball consists of a ball shaped disk .this ball shape disk rotates to stop or start flow. The ball has a hole, or port, through the middle so that when the port is in line with both ends of the valve, flow will occur.The ball performs the same function as the disk in the globe valve.
Table of Contents
- What is a Floating Type Ball Valve?
- How does a Floating Ball Valve work?
- Components of Ball Valve Floating Type
- Types of Ball Valve
- Differences between Floating Ball Valve & Trunnion Ball Valve
- 1. Appearance of Floating Ball Valve vs Trunnion
- 2. Sealing surface of Trunnion vs Floating Ball Valve
- 3. Working principle of Floating vs Trunnion Ball Valve
- 4. Application of Trunnion Ball Valve vs Floating
- 5. Characteristics of Ball Valve Trunnion vs Floating
What is a Floating Type Ball Valve?
In a floating ball valve, the ball is suspended in the flowing fluid and is kept in position by the compression of two elastomeric seats against it.
The shaft is connected at the top of the ball and allows the switch from an open to a closed position with a quarter turn movement (90 degrees).
When the shaft is moved, a load is applied to the ball which gets pressed against its seats.
This design, which is lightweight and economic, suits bore sizes up to 10 inches: above this bore size, the seats of the valve would not be able to withstand heavier and heavier balls and the valve would not operate safely and efficiently.
Floating ball valves allow a bi-directional shut-off of the flow (as the trunnion type).
How does a Floating Ball Valve work?
Floating ball valves are operated by a shaft, or stem, attached to the top of the ball that turns it 90 degrees (a quarter turn). As the ball rotates, the port is covered or uncovered by the wall of the valve body, either releasing or halting the flow of media. The stem is attached loosely enough to the ball that, as the ball rotates on its axis, the pressure of the flow pushes the ball against its downstream seat, creating a tight seal. For this reason, floating ball valves may not seal as effectively in very low pressure applications after a certain amount of seat wear has occurred. This is because there may not be enough media pressure to force the ball against the downstream seat to create a tight seal. However, in most applications downstream pressure is sufficient to maintain a tight seal long after the seats have begun to wear.
Components of Ball Valve Floating Type
The major components of a floating ball valve include:
Valve body – A pressure vessel that contains the components needed to control or shut off the flow through a pipe. It is designed to connect two or more sections of pipe or tubing to each other.
Ball – A sphere with a flow path (hole or tunnel) through the center of it and a connection point for a shaft to rotate it.
Seats – Round donut-shaped discs that form a seal between the body and ball.
Stem – A shaft that connects the internal ball to the outside of the valve to facilitate rotation of the ball.
Packing – Flexible seals that fit around the shaft and prevent the media traveling through the valve from escaping externally.
Bonnet – The part of the valve body that houses the stem and packing.
Operator or Actuator – An external device designed to rotate the stem of the valve. This can be a lever, a gear, a motor-operated gear (electric actuator), or a pneumatic/hydraulic actuator.
Types of Ball Valve
Based on Ball Design
The most common design is the “floating ball design”. The ball is suspended in the media and held in place by two sealing rings. Some high-quality valves have a “trunnion ball design”. The ball is supported at the top and bottom to reduce the load on the valve seats.
- Floating Ball Valve – The majority of ball valves have a floating ball. The ball is supported by the valve seats.
- Trunnion Ball Valve – Valves with large diameters and high operating pressures (for example DN >100mm and 30 bar) have often a trunnion design. The ball is supported on the bottom and top to reduce the load on the seat rings. The operating torque is generally lower for trunnion valves.
The hole through the ball may have different profiles such as a full bore, reduced bore or V-shaped.
- Reduced bore Ball Valve – Most ball valves have a reduced bore. As a result, the ball valve introduces friction losses in the system. These losses are still relatively small compared to other types of valves. One-piece ball valves are almost always reduced bore.
- Full bore Ball Valve – Full bore valves have the same bore diameter as the pipe. The advantage is that there are no extra friction losses, and that the system is mechanically easier to clean (pigging). The downside is that the ball and the housing are bigger than a standard ball valve with reduced bore. The cost is therefore slightly higher, and for many applications this is not required.
- V-shaped Ball Valve – The hole in the ball or the valve seat has a “V” shaped profile. As a result, the desired flow rate can be controlled more precisely by rotating the ball. By optimizing the profile, a linear flow characteristic can be approached.
Differences between Floating Ball Valve & Trunnion Ball Valve
What are the differences between floating ball valve & trunnion ball valve. There are major 5 points.
1. Appearance of Floating Ball Valve vs Trunnion
The floating ball valve and the trunnion ball valve are easy to distinguish in appearance. If the valve body has a fixed shaft on the bottom, it must be the trunnion ball valve.
If the ball valve body has a device for injecting grease,it is basically a trunnion ball valve.However, if there is no injecting device,can we say it must be a floating ball valve? This is incorrect, because small size such as 2 “150LB trunnion ball valves are usually not filled with injecting device either.
2. Sealing surface of Trunnion vs Floating Ball Valve
As the ball of the floating ball valve is floating, so under the pressure of the medium, the floating ball will move and against the downstream seat., so the seal of the floating ball valve belongs to the single-side seal.The ball of the trunnion ball valve cannot be moved, so the two sides of the trunnion ball valve both must be sealed.
Since the sealing principle is different, the requirements of the two ball valves on the sealing surface material are different, especially the sealing surface of the floating ball valve must be able to bear the pressure caused by the floating ball.
3. Working principle of Floating vs Trunnion Ball Valve
The floating ball valve only has upper stem and the ball can have a slight displacement, so it is called floating ball valve.The trunnion ball valve ball has another stem at the bottom to fixed the position of the ball,so the ball can’t move.
The sealing of the floating ball valve is realized by the pressure of the medium, when the ball valve is closed, the floating ball is pressed against the sealing surface under the action of pressure to realize sealing.When the trunnion ball valve is closed, the ball does not produce displacement, but the floating seats will move and press against the ball under the action of the media pressure to realize sealing.
4. Application of Trunnion Ball Valve vs Floating
The floating ball valve is suitable for medium and low pressure and usually has a small diameter.The trunnion ball valve can be used in high pressure conditions and the size can be up to 60 inches.
The trunnion ball valve is a kind of double-block-and-bleed(DBB) valve, while the floating ball valve only seal the downstream side. The trunnion ball valve can block both upstream and downstream media. And when the pressure in the middle cavity is greater than the seat spring force, the seat will be pushed open to release the pressure inside the chamber to ensure safety.
5. Characteristics of Ball Valve Trunnion vs Floating
To the floating ball valves, the trunnion ball valves are usually used longer, has smaller size and easier to operate.
The trunnion ball valve also has the function of automatic release pressure, when the medium temperature in the valve rises and causes abnormal pressure rise, the trunnion ball valve can automatically release the pressure without a relief valve,This is very important to ensure the safety of industrial production.
Related Tags :
ZECO Valve
Ball Valve Manufacturer – Various Ball Valve Types
Difference Between Floating Ball Valve & Trunnion Ball Valve
Shanghai Pressure Reducing Valve Factory
Thermoplastic Materials as Ball Valve Seat & Butterfly Valve Seat
Difference Between Gate Valve And Butterfly Valve
Gate Valve vs Ball Valve
Manual Operate Gate Valve Manufacturer
Globe Valve vs Ball Valve
Ten articles before and after
What is High Performance Butterfly Valve – Zeco Valve Company | Professional valve manufacturer
What is Jacketed Valve – Zeco Valve Company | Professional valve manufacturer
What is Monoblock Ball Valve – Zeco Valve Company | Professional valve manufacturer
WHAT IS PLUG VALVE – Zeco Valve Company | Professional valve manufacturer
What are Jacketed Valves – Zeco Valve Company | Professional valve manufacturer
Wish All Clients Happy New Year 2020 – Zeco Valve Company | Professional valve manufacturer
Full port ball valve VS reduced port ball valve – Zeco Valve Company | Professional valve manufacturer
Zeco supplies A217 C5 Valve for the refinery – Zeco Valve Company | Professional valve manufacturer
Zeco ATEX CERTIFICATE – Zeco Valve Company | Professional valve manufacturer
Pnematic Control Valve – Zeco Valve Company | Professional valve manufacturer